Factory-Direct 200W Single Output Waterproof Switching Power Supply

1. The input voltage of the waterproof switching power supply should be selected according to the design of the circuit. Generally, there are two kinds of input voltage: 220 volts and 110 volts. If you choose improperly, it will damage the switching power supply. 2. Do not connect the ground wire and neutral wire end of the output voltage wiring wrongly, and make sure that the grounding is reliable. 3. After the switching power supply is installed, it is necessary to conduct a power-on trial operation, check the condition of each part, and ensure that it can be powered on after it is normal. Finally, pay attention to the heat dissipation of the waterproof switching power supply. It is best to install the switching power supply in a position with good air convection conditions, so that the heat can be easily dissipated.200W Single Output Waterproof Switching Power Supply LDV-200 series High efficiency, High reliability, Low cost Protections: Short circuit/Over load/Over voltage/High temperature Waterproof grade: IP67 Working Frequency: 65 KHz Suitable for LED lighten and moving sign applications. 2 years warranty

Note on the use of waterproof power supply

Specifications

SPECIFICATION
OUTPUT
Model	LDV-200-12	LDV-200-24	LDV-200-36
DC Voltage	12V	24V	36V
Rated Current	16.5A	8.3A	5.5A
Current Range	0-16.5A	0-8.3A	0-5.5A
Rated Power	198W	199W	198W
Ripple & Noise	150mVp-p	200mVp-p	200mVp-p
Voltage Tolerance	±1%	±1%	±1%
Inlet Stability	±0.5%	±0.5%	±0.5%
Load Stability	±0.5%	±0.5%	±0.5%
Setup, Rise, Hold Up Time	200ms,20ms,30ms/230VAC
INPUT
Voltage Range	180～264 VAC 47～63Hz；255～373VDC
AC Current	1.5A/230VAC
Efficiency	82%	84%	85%
Inrush Current	Cold-start current 40A/230VAC
PROTECTION
Over Load	105%~135%
	Protection：Hiccup mode, recovers automatically after fault condition is removed
Over Voltage	30~32V		42~44V
	Protection：Hiccup mode, recovers automatically after fault condition is removed
High Tem.	≥85℃
	Protection：cut off the output, recovers automatically after fault condition is removed
ENVIRONMENT
Working Temp., Humidity	-10℃~+60℃,20%~90%RH
Storage Temp., Humidity	-20℃~+85℃, 10%~95%RH
Temp. Coefficient	±0.03%/℃(0-50℃)
Vibration	10-500Hz,2G 10min,/1cycle,Period for 60min,Each axes
SAFETY
Withstand Voltage	I/P-O/P: 3KVAC I/P-FG: 1.5KVAC O/P-FG: 0.5KVAC
Isolation Resistance	I/P-O/P, I/P-FG, O/P-FG: 100M Ohms/500VDC
STANDARD
Safety Standard	EN61347-1 EN61347-2-13 IP67
EMC Standard	EN55015 EN61547 EN61000-3.4 CLASSB
OTHERS
Dimension	2156943（LWH）
Weight	1.3Kg
NOTE	1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
	2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
	3. Tolerance: includes set up tolerance, line regulation and load regulation.